Most ACP problems are preventable. Delamination, fading, staining, edge lifting, bubbling and fixings failure usually trace back to weak specification, poor material quality, incorrect installation or inadequate maintenance. Recognizing these defects early and understanding their causes helps buyers and contractors avoid costly repairs. This guide covers the most common ACP panel problems, how they appear, what causes them and the practical steps to prevent them. FEITENG produces building grade ACP to consistent quality standards, and this article draws on our experience supporting installations worldwide.
ACP failures rarely have a single cause. A panel may be under-specified for its environment, manufactured with thin skins or weak bonding, fixed without movement allowances, or maintained with the wrong cleaners. Because the material, installation and upkeep all interact, a problem that appears on the finished facade can originate at any stage of the project. Identifying the root cause matters because treating the symptom without fixing the underlying issue usually leads to recurrence.
The good news is that the majority of common defects are well understood and can be avoided through careful specification, a reputable supplier, competent installation and a basic maintenance routine.
Delamination is one of the most serious ACP defects. It appears as bubbling at the panel face, lifting at the edges or a visible separation between the aluminum skin and the core. Causes include weak bonding during production, contaminated or poorly pretreated surfaces, moisture trapped in the core, or impact that breaks the bond. Once delamination starts, water can enter the cavity and worsen the damage, so affected panels should be assessed promptly.
Prevention starts with supplier quality: choose a manufacturer with controlled bonding processes and adhesion testing. During installation, avoid exposing panel edges to standing water, and seal edges where required. If delamination appears, small areas may be monitored, but panels with widespread bubbling or edge separation usually need replacement to prevent water ingress.
Fading shows as a loss of color intensity, especially on dark or dark-colored panels in strong sunlight. Chalking appears as a powdery surface residue when the coating breaks down over time. These problems usually result from using a PE coating in an exposed outdoor location, low-quality paint, or inadequate surface pretreatment. Over time, a weak coating can craze, crack or peel away from the aluminum skin.
To prevent fading, specify a PVDF coating for exterior facades and exposed signs, and confirm the skin gauge and pretreatment quality. Choose colors appropriate to the climate, and avoid abrasive cleaners that accelerate coating wear. Our comparison of PE and PVDF finishes explains which coating suits which exposure.
Staining comes from several sources: dust and pollution settling on the panel, bird droppings, graffiti, grease in kitchen settings, or water carrying minerals down the face. Water marks form when water evaporates and leaves deposits behind. Surface scratches usually occur during transport, handling or construction, before the protective film is removed.
Most surface staining is manageable with regular washing using mild, pH-neutral cleaners and soft cloths. Avoid bleach, solvents, abrasive pads and steel wool, which can damage the finish. Keep the protective film in place until installation is complete, then remove it within the recommended period to prevent adhesive residue. For routine upkeep, see our guide to cleaning and maintaining ACP panels.
Many facade problems are installed rather than manufactured. Common installation defects include rigid fixing without thermal movement allowance, poorly sealed joints, panels fixed to an inadequate sub-frame, and water trapped behind the panel. These can show up as buckling, popped fixings, sealant cracking or corrosion around fixings. In signage applications, over-tightened fixings or an unstable frame can cause the board to flex or loosen over time.
Good installation uses a secure sub-frame, aligned fixings, flexible sealants and proper edge sealing. The installer should allow for panel movement and ensure drainage behind the panel. Reviewing installation details before fitting prevents the most avoidable post-completion problems.
| Defect | Typical Cause | Prevention |
|---|---|---|
| Delamination / edge lifting | Weak bond, contaminated surface, moisture ingress | Quality supplier, adhesion testing, sealed edges |
| Fading / chalking | PE coating outdoors, weak paint, poor pretreatment | Specify PVDF for exposed facades |
| Surface staining | Pollution, droppings, grease, water deposits | Regular mild cleaning, avoid harsh chemicals |
| Scratches / film residue | Rough handling, late film removal | Keep film on until fit-out, handle carefully |
| Buckling | No thermal movement allowance, rigid fixing | Allow movement, use proper sub-frame and fixings |
| Sealant / fixing failure | Poor sealing, corrosion at fixings | Quality sealants, corrosion-resistant fixings |
| Impact damage | Thin skin, impact in vulnerable locations | Choose adequate thickness and skin gauge |
Schedule periodic inspections, especially on exposed facades and coastal or industrial sites. Check fixings, sealant, edges, surface finish and any signs of bubbling or corrosion. Small chips can be touched up with matching paint from the panel supplier, and cracked sealant should be replaced promptly. Panels showing widespread delamination, deep impact damage or core exposure should be repaired or replaced to prevent water ingress.
If problems appear after installation, document the condition with photos, note the location and date, and contact the supplier or installer with the batch and order details. A traceable manufacturer can help identify whether the issue relates to material, fabrication or installation. FEITENG's technical and quality background is described on the technology and testing page, and completed installations can be reviewed in the case galleries.
It is worth noting that defects often surface only after months or seasons of use, which is why a one-time inspection immediately after installation is not enough. A panel may look sound at handover but reveal subtle coating fading, sealant shrinkage or slight edge movement after its first summer or winter. Building owners and contractors should therefore treat inspection as a recurring duty rather than a single handover check. Keeping a simple log of inspections, repairs and replacements makes it easier to track recurring problems and to hold whichever party was responsible accountable if a pattern emerges.
What causes ACP panels to delaminate?
Delamination usually comes from weak bonding, contaminated or poorly pretreated surfaces, moisture trapped in the core, or impact that breaks the skin-to-core bond. It appears as bubbling, edge lifting or separation.
Why do ACP panels fade?
Fading often results from using a PE coating in a strongly exposed outdoor location, low-quality paint or inadequate surface pretreatment. PVDF coatings resist UV and fading far better on exposed facades.
How do I remove stains from ACP without damaging the finish?
Wash with clean water and a mild, pH-neutral detergent using a soft cloth or sponge. Avoid bleach, solvents, abrasive pads, steel wool and concentrated acids or alkalis, which can scratch or craze the coating.
Can buckling be fixed without replacing panels?
Minor buckling from thermal movement may be relieved by adjusting fixings and ensuring movement clearance. Severe buckling, delamination or impact damage usually requires panel replacement.
How often should ACP cladding be inspected?
At least annual inspection is recommended for exterior facades; coastal, industrial and poolside locations may need more frequent checks. Inspect fixings, sealant, edges and surface condition each time.
About this article: FEITENG has produced metal composite panels since 1994, with 15 production lines and ISO9001, ISO14001, ISO45001, CE, UL, SGS, CTC and CQC certifications. This defect guide is for specification and maintenance guidance and does not replace a site inspection by a qualified installer. For panel enquiries, contact FEITENG.
Zhangjiagang Feiteng New Composite Materials Co., Ltd.
Address:No.77 Huada Road, Environmental & New Material Industry Park, Bonded Port Zone, Zhangjiagang City, Jiangsu, China
Phone:+86 18151586877
E-mail:info@feitengacp.com
COPYRIGHT © Feiteng All RIGHTS RESERVED.