Behind every flat, durable aluminum composite panel is a carefully controlled production line. Understanding how ACP is made helps buyers judge quality, ask better technical questions and compare suppliers with confidence. This article walks through the full aluminum composite panel manufacturing process, from coil preparation and surface treatment to bonding, coating, slitting and final inspection. FEITENG has focused on metal composite panel production since 1994, running 15 production lines at our 110,000 sqm factory; the steps below reflect how our panels are actually produced and tested.
Every ACP order begins with the incoming materials: aluminum coils for the face and back skins, polyethylene or mineral-filled material for the core, and coating resins for the finish. Reputable manufacturers inspect each batch on arrival. Aluminum is checked for alloy grade, thickness consistency and surface condition, while core material is checked for purity, density and fire-performance characteristics. Weak incoming inspection is one of the earliest warning signs of a low-quality panel, because defects in the raw material cannot be fully repaired later in production.
At this stage, suppliers also confirm that materials comply with the relevant international directives and standards. FEITENG, for example, ensures its panels comply with REACH and RoHS requirements, and our production is covered by ISO9001, ISO14001 and ISO45001 management systems. Buyers can read more about our testing capabilities on the ACP technology and testing lab page.
The aluminum coils are uncoiled and fed through cleaning and pretreatment lines. The surface is degreased to remove rolling oil and contaminants, then chemically treated to create a micro-roughened, corrosion-resistant layer that improves paint adhesion. Poor pretreatment leaves the coating prone to peeling or discoloration even when the paint itself is high quality. After treatment, the coil is dried and inspected for any marks or oxide spots before moving to the coating section.
For exterior-grade panels, the quality of this pretreatment step directly affects service life. A well-prepared aluminum skin creates a stable base that locks the coating to the metal, resisting the repeated wetting, drying and UV exposure that facades experience over decades.
Many ACP lines apply the coating to the aluminum coil before lamination. Polyester (PE) coatings are economical and work well for indoor and light-duty outdoor use. PVDF (polyvinylidene fluoride) coatings are more expensive but offer superior weather resistance, UV stability and color retention for exposed facades and coastal locations. The coil passes through coating applicators that lay down a uniform film, then enters an oven where the coating cures to a hard, durable finish. Color batches are matched against approved samples before production continues.
If you are deciding between finishes, our article comparing PE and PVDF coated ACP explains the trade-offs in cost, durability and suitable applications. The choice of coating is independent of panel thickness, so a 4 mm facade panel can be specified with either a PE or a PVDF topcoat depending on exposure.
The core lamination step bonds the two aluminum skins to the core under heat and pressure. The core material is fed between the prepared aluminum sheets, and the sandwich passes through heated rollers that activate the bonding layer and compress the materials into a uniform board. Temperature, pressure and line speed must be tightly controlled: too little heat or pressure leads to weak adhesion and later delamination, while excessive heat can deform the core or damage the finish.
A well-bonded panel shows no air pockets, no edge separation and a consistently flat surface. Delamination, which appears as bubbling or lifting at panel edges, is almost always traced back to insufficient bonding pressure, contaminated surfaces or moisture trapped in the core. This is why factory adhesion testing is such an important part of quality control.
After bonding, many panels receive a protective polyethylene film on the face surface. This film shields the finish from scratches, dust and construction-site dirt during transport and installation, and is peeled off once the installation is complete. Some product families also use film lamination to add texture, matte finishes or decorative effects. The protective film must be removed within the recommended period to avoid adhesive residue, especially in hot climates.
FEITENG also produces film-laminated metal composite panels as a distinct product line; these panels combine the structural stability of ACP with a decorative laminated face. You can view finished examples in the film-laminated panel project gallery.
The wide composite board is then slitted to width and guillotined to the required length. Edge quality matters: clean, square edges make installation faster and reduce the risk of water ingress or edge cracking. Panels that will be engraved, folded or folded back for fabrication are checked for consistent thickness and flatness before leaving the cutting section. Custom sizes are cut against a verified cutting list to minimize material waste.
Pre-roll coated aluminum sheets follow a parallel coating-and-slitting process and are used as raw material for other composite products. FEITENG produces these alongside its ACP lines, which allows tighter control over material consistency across the product range.
Quality control runs through every stage, not just at the end. In-line checks monitor thickness, flatness, coating thickness and color consistency. Finished panels are tested for adhesion, impact resistance, bend flexibility, weather resistance and fire performance as required. Records are kept so that any customer complaint can be traced back to the production batch, coil lot and inspection results. This traceability is one of the signs of a professional manufacturer rather than a simple assembling workshop.
Independent certifications provide an additional external check. FEITENG holds CE, UL, SGS, CTC and CQC certifications alongside its ISO management certifications, and our products reach customers in more than 56 countries. Prospective buyers often ask to see test reports, factory videos and sample finishes before placing a bulk order.
| Production Stage | Main Activity | Quality Risk Controlled |
|---|---|---|
| Incoming inspection | Check aluminum coil, core and coating batch | Defective raw material |
| Surface treatment | Degrease and chemically treat aluminum surface | Poor paint adhesion, corrosion |
| Coil coating | Apply and cure PE or PVDF topcoat | Fading, uneven color |
| Bonding | Heat and pressure bond skins to core | Delamination, weak adhesion |
| Film lamination | Apply protective or decorative film | Surface damage in transport |
| Slitting and cutting | Slit to width and cut to length | Poor edges, out-of-square panels |
| Final inspection | Adhesion, impact, bend, weather and fire tests | Non-conforming finished panels |
How are aluminum composite panels made?
ACP is made by bonding two thin aluminum skins to a polyethylene or mineral core under heat and pressure, after the aluminum coils have been cleaned, pretreated and coated. The finished board is then slit, cut and inspected before packaging.
What is the difference between coating and core in ACP production?
The coating is the painted finish on the face skin (PE or PVDF), which controls weather resistance and color retention. The core is the center material (PE or mineral-filled), which determines the panel's fire behavior. They are selected independently.
How do manufacturers prevent delamination?
Delamination is prevented through clean surface preparation, controlled bonding temperature and pressure, and adhesion testing at both in-line and final inspection stages.
What tests should a quality ACP panel pass?
At minimum, panels should pass adhesion, impact, bend flexibility and dimensional stability tests. Exterior and fire-rated panels should also meet weather and fire-classification requirements, with available test reports and third-party certifications.
Can I visit or audit an ACP factory before ordering?
Yes. Professional suppliers welcome factory visits, video audits and sample requests. Review the production lines, testing lab and quality records, as described on the about FEITENG page, before committing to a bulk purchase.
About this article: FEITENG (Zhangjiagang Feiteng New Composite Materials Co., Ltd.) has produced metal composite panels since 1994, with 15 production lines, a 30,000 sqm daily output capacity and certifications including ISO9001, ISO14001, ISO45001, CE, UL, SGS, CTC and CQC. This process overview reflects our own manufacturing experience. For samples or production details, contact the FEITENG team.
Zhangjiagang Feiteng New Composite Materials Co., Ltd.
Address:No.77 Huada Road, Environmental & New Material Industry Park, Bonded Port Zone, Zhangjiagang City, Jiangsu, China
Phone:+86 18151586877
E-mail:info@feitengacp.com
COPYRIGHT © Feiteng All RIGHTS RESERVED.